topic No Server in QlikView

No Server

Mon, 26 Jan 2026 18:19:17 GMT

Good day everybody,

i'm facing a "no server" error when i reach the access point

context :

i'm working on a VM.

QVS (v9) is set, all QV services are started (IIS is running too),

my user administrator is located in Qlikview administator group and i can run QMC and QEMC

My users are declared

Pb:

whan i launch internet on http://localhost/qlikview i reach the access point.

I authentified either as a user or administrator but get "No server".

can somebody explain to me what is wrong?

thank you

chris

No Server

SunilChauhan — Tue, 23 Aug 2011 09:35:04 GMT

use http://your Ip address/qlikview

i belive u require to access from server so u need to access using

ex:

http://10.20.30 http://10.20.30.4.4 http://10.20.30.40/qliview

No Server

Tue, 23 Aug 2011 09:54:28 GMT

HI sunil,

i did use my http://localhost/qlikview address. Because everything is set on my VM and i'm testing on it

I tries as well with 127.0.0.1 which is the same

christian

No Server

Miguel_Angel_Baeyens — Tue, 23 Aug 2011 10:01:15 GMT

Christian,

Probably asking the obvious but is the service actually running? Check in the Windows Startup button, Run, Services.msc and make sure that all services that start with "QlikView" are up and running. In addition to this, if you just have installed the server, you will need to reboot your computer so the permissions and users created during the install are working fine.

If you can get to the QEMC, check the Status tab, "Services" menu and all servers show the correct server name and "Running" status.

Hope that helps.

Miguel Angel Baeyens

BI Consultant

Comex Grupo Ibérica

No Server

Tue, 23 Aug 2011 10:30:21 GMT

Hello Miguel Angel

thak's for the answer but every thing is running normally

that's the reason i don't undrrstand why i get "no server" message

regards

christian

No Server

Miguel_Angel_Baeyens — Tue, 23 Aug 2011 10:48:40 GMT

Christian, is the QlikView WebServer running as well? It may conflict with the IIS if both are listening to port 80 (check here), so the client might get an answer from the incorrect web server. Anyway, check this post and this thread regarding to your issue.

Hope that helps.

Miguel Angel Baeyens

BI Consultant

Comex Grupo Ibérica

No Server

Tue, 23 Aug 2011 10:56:05 GMT

Miguel

i found it.

the sercver connection name was simply not defined!!

have a good day

christian

No Server

Tue, 23 Aug 2011 10:56:27 GMT

Sunil,

i found it.

the sercver connection name was simply not defined!!

have a good day

christian

No Server

SunilChauhan — Tue, 23 Aug 2011 11:18:16 GMT

i believe server connection name and server ip is one and the same.is it right.

can u please get back on this.

No Server

shumailh — Wed, 26 Oct 2011 09:09:24 GMT

Christian,

I am gettign the same message can you please let me know how to define the server connection name in QlikView?

Regards,

Shumail Hussian

No Server

Mon, 16 Jan 2012 06:48:18 GMT

Hi Sunil

Could you please tell me, how to define the server connection name in QlikView?

Anta

No Server

Mon, 16 Jan 2012 07:37:59 GMT

Hi All, If both servers (Web and IIS are running) is not the easy installation procedure. We have to change the port no in config file then only it will connect u to server and shows the document. Regards, Ravi.

Re: No Server

Thu, 19 Jan 2012 13:13:59 GMT

Hi chaps,

sorry fir the delay but i've been out of the community for a big while.

As far as I remember, use QEMC, tabs System, Setup, General to set the server

name.

bets regards

christian

Selon a_thodge <qliktech@sgaur.hosted.jivesoftware.com>:

a_thodge created the
discussion
"Re: No Server"
To view the discussion, visit:
http://community.qlik.com/message/182736#182736

Re: No Server

g_westaway — Mon, 30 Apr 2012 17:48:04 GMT

There was another explanation for the 'No Server' scenario in our installation (v10).

We switched to using Custom User authentication for named users, via the AccessPoint (having upgraded to v10 a few weeks earlier). After that, once or twice per day, the AccessPoint after logging in just showed "No Server".
When checking the QV server, the QVS service shows as 'Disconnected' with a message "Failed to contact service".
However the QlikView windows services all appear to be running normally.

QV support said this was just lack of resources on the server, but didn't explain why this had suddenly become such a factor.
Checking the session log, it showed all ‘Named user’ connections using tunnelling, not port 4747.
I had earlier noticed that huge logs were being generated by the web server, mostly full of encrypted text following a tunnel request.
It seemed something was blocking port 4747 between the web server and the QV server.

After we added the NAT IP address (or the DNS name) of the server in the "Link Machine Name" attribute under QEMC > Setup > Server > General > External Linking, all ‘Named user’ connections then used port 4747. Since then, we have had no further instances of this error.

I hope this might help
Giles

Re: No Server

Thu, 18 Jul 2013 19:45:05 GMT

I confirm -- adding Link Machine Name in QMC -> System -> Setup -> QlikView Servers -> General solves the problem.

Re: No Server

luciano_garcia — Wed, 03 May 2017 19:46:40 GMT

I confirm too. I was able to fix the problem just by putting the web server name on the line described above as you recommended and clicking on "Apply". Access has been normalized and the following messages are no longer returned in EventViewer :

Thank you.