Qlik Community

App Development

Discussion board where members can learn more about Qlik Sense App Development and Usage.

Announcements
IMPORTANT security patches for GeoAnalytics Server available to download: READ DETAILS
cancel
Showing results for 
Search instead for 
Did you mean: 
shree909
Partner
Partner

Calling the Bookmarks in the qliksense with a url

Hi Folks,

I have a scenario where i want to call  the bookmarks directly with the url

For that i have a  bookmark id,

Example:  Https:// localhost/sense/appid/bookmark/qjdl

https://xxx.xxxx.xxxx.xxxx//sense/app/d6bd61616/bookmark/qJdJ


For the standard URL I tried appending  the bookmarks

Tried with bookmark/qJdJ and Bookmark =qJdJ nothing works.


when i access this url its not opening the bookmark page.

Is there a way that we can call the bookmarks directly from the url.

i know in qlikview it works   but not in sense???

https://community.qlik.com/blogs/qlikviewdesignblog/2014/07/11/ajax-and-url-parameters#start=25

1 Solution

Accepted Solutions
StefanBackstrand
Employee
Employee

So, this works from 2.0. There are two ways, as I see it;

Have the bookmark in the URL

The syntax for bookmarks in the URL took some figuring out, but I got this working: https://mysenseserver/sense/app/4855acdb-2ab7-490b-9638-f34bd5d0723e/sheet/etGmEPq/state/analysis/bo...

That was on a 2.2 server. I got the bookmark ID from the Single Configurator, since the QMC does not show them for some reason.

Use the Single Configurator in the dev-hub

The Single Configurator is located at https://mysenseserver/dev-hub‌ (2.2) or https://mysenseserver/single (2.0, 2.1), and will allow to reference a single object via a link, and it would be any object - sheet or chart object. The URL to a single would be something like https://mysenseserver/single?appid=2511d22e-091f-4dee-b92b-d07042a3c42a&sheet=XPFUjr&opt=nointeracti...

It can contain either a selected bookmarks, or any combination of selections. It's very powerful.

View solution in original post

6 Replies
Not applicable

Hi,

Try https://xxx.xxxx.xxxx.xxxx//sense/app/d6bd61616?bookmark=qJdJ


Best regards

André R. Ferreira

shree909
Partner
Partner
Author

Thanks for ur respose Andre, But that dint work....

Not applicable

I am also looking for solution to this.  I would like to be able to open the bookmark with single URL.

StefanBackstrand
Employee
Employee

So, this works from 2.0. There are two ways, as I see it;

Have the bookmark in the URL

The syntax for bookmarks in the URL took some figuring out, but I got this working: https://mysenseserver/sense/app/4855acdb-2ab7-490b-9638-f34bd5d0723e/sheet/etGmEPq/state/analysis/bo...

That was on a 2.2 server. I got the bookmark ID from the Single Configurator, since the QMC does not show them for some reason.

Use the Single Configurator in the dev-hub

The Single Configurator is located at https://mysenseserver/dev-hub‌ (2.2) or https://mysenseserver/single (2.0, 2.1), and will allow to reference a single object via a link, and it would be any object - sheet or chart object. The URL to a single would be something like https://mysenseserver/single?appid=2511d22e-091f-4dee-b92b-d07042a3c42a&sheet=XPFUjr&opt=nointeracti...

It can contain either a selected bookmarks, or any combination of selections. It's very powerful.

reddy-s
Master II
Master II

Hi Shree,

Use the Single Configurator to get the url when a book mark is selected. This will give you the right URL.

rbartley
Specialist
Specialist

In fact, the relevant bit of the URL is bookmark=....... .  You can just add "?bookmark=....." to the URL (or "&bookmark...." if you already have other parameters in your URL) and it will apply the bookmark.