Qlik Community

New to Qlik Sense

Discussion board where members can get started with Qlik Sense.

Not applicable

Bell curve

Hi all,

hic

I need to draw a bell curve for the below data.

Please help me to do it.

I used the below link to prepare:

Recipe for a Histogram

I have done to some extent but i am not sure that it is correct. please do check and clarify.

I have attached sample data and .qvf file.

Regards,

Pramod

1 Solution

Accepted Solutions
Employee
Employee

Re: Bell curve

If you use a calculated dimension for a histogram, everything will become very complicated... Hence, you should define your dimension field already in the script. Then it is straightforward.

Image1.png

But I am not sure the data fits a normal distribution...

HIC

4 Replies
Employee
Employee

Re: Bell curve

If you use a calculated dimension for a histogram, everything will become very complicated... Hence, you should define your dimension field already in the script. Then it is straightforward.

Image1.png

But I am not sure the data fits a normal distribution...

HIC

Not applicable

Re: Bell curve

Thanks a lot henric cronstrom,

Now it's working fine.

Regards,

pramod

Not applicable

Re: Bell curve

Hi Henric,

hic

1)  your reply was most helpful. But one issue. I was using below script to load the data for 5 minutes time interval:

LOAD *,

  If(total_time_taken<='00:05:00' ,Dual('00:00-05:00',0),

If(total_time_taken>='00:05:00' and total_time_taken<='00:10:00' ,Dual('05:00-0:10:00',1),

If(total_time_taken>='00:10:00' and total_time_taken<='00:15:00' ,Dual('10:00-15:00',2),

If(total_time_taken>='00:15:00' and total_time_taken<='00:20:00' ,Dual('15:00-20:00',3),

If(total_time_taken>='00:20:00' and total_time_taken<='00:25:00' ,Dual('20:00-25:00',4),

If(total_time_taken>='00:25:00' and total_time_taken<='00:30:00' ,Dual('25:00-30:00',5),

If(total_time_taken>='00:30:00' and total_time_taken<='00:35:00' ,Dual('30:00-35:00',6),

If(total_time_taken>='00:35:00' and total_time_taken<='00:40:00' ,Dual('35:00-40:00',7),

If(total_time_taken>='00:40:00' and total_time_taken<='00:45:00' ,Dual('40:00-45:00',8),

If(total_time_taken>='00:45:00' and total_time_taken<='00:50:00' ,Dual('45:00-50:00',9),

If(total_time_taken>'00:50:00',Dual('>50:00',10)

))))))))))) as time_interval;

but now i need show the data for every 1 minute interval , so i need to hard code like below,

If(total_time_taken>='00:01:00' and total_time_taken<='00:02:00' ,Dual('01:00-02:00',1),

If(total_time_taken>='00:02:00' and total_time_taken<='00:03:00' ,Dual('02:00-03:00',2),

Is their any other way to display without hard coding ?

2)  I need to display the data values of bar in combo chart. how can i done this.

3) I need to disable the selection so, i have using {1}, but how this can be used for below expression: which should be applied for whole expression:

only(Normdist(round(total_time_taken,avgTime),Avg({1<subject_id={'2'},subject_status={'passed','completed'}>}total total_time_taken),

Stdev({1<subject_id={'2'},subject_status={'passed','completed'}>}total total_time_taken),1))

*avgTime*Count({1<subject_id={'2'},subject_status={'passed','completed'}>}total_time_taken)

Thanks,

Pramod

MVP
MVP

Re: Bell curve

This discussion is closed -  I suggest that you start a new discussion for this question.