Qlik Community

New to Qlik Sense

Discussion board where members can get started with Qlik Sense.

Not applicable

Doubts regarding Qliksense

Hi all,


As i started exploring QlikSense recently, I am unclear  about these following doubts:


1) Does Latest version of Qliksense supports Alternate State.

2) Can we place one object on another (Overlapped).

3) Can we make disappear chart from sheet based on condition.

4) Does latest QlikSense Supports Trigger and action?, if yes then please give detail about what type of action ?

5) Can we get object ID of object on sheet like QlikSense, if yes then how ?

6) Can we conditionally evaluate expression in QlikSense ?

7 Replies
kashaboinaraj
Contributor

Re: Doubts regarding Qliksense

Hi devanand

No alternate state in qlik sense as of now. However, there are extensions that can help you, check : Re: alternate states in qlik sense

There is already an extension existing for this,Check this out:http://branch.qlik.com/#/project/56728f52d1e497241ae698a7

Regards

vishnu

paul_scotchford
Valued Contributor

Re: Doubts regarding Qliksense

The extension works but has limitations, it would be nice if AS was native to QS like with QV. but it does give you the minimal requirements for Comparative analysis.

Overlays are not currently supported.

Triggers can be kind of done using the navigation extension from QlikBranch but not as good as QV as the extension supports this.

Object ID's like QlikView, I will check into this as I have not had a requirement such as in QV.

What are you expecting with conditional evaluation per se ? Of course you can use IF and Set Analysis to evaluate whether to calculate across a selection, is this what you mean ?

Perhaps a lot of these questions will be addressed in the next scheduled release of QlikSense fingers crossed.

reddys310
Honored Contributor II

Re: Doubts regarding Qliksense

Hi Devananda,


1) Does Latest version of Qliksense supports Alternate State.

Its not currently available and highly expected in the next release (Feb)


2) Can we place one object on another (Overlapped).

Placing one object over other is not possible in qliksense and the reason being its responsive belhaviour. Its more of a Pro than a Con as QlikSense is very intuitive when viewed on mobile devices as well.


3) Can we make disappear chart from sheet based on condition.

This is not implicitly possible but if you would like to develop some think like this its totally possible using extensions.


4) Does latest QlikSense Supports Trigger and action?, if yes then please give detail about what type of action ?

Again this can be expected soon. But you already have the leverage to develop triggers your self using extensions.


5) Can we get object ID of object on sheet like QlikSense, if yes then how ?

Yes you can : Check this out: http://localhost:4848/single - this will give you the object id of sheet/visualization


6) Can we conditionally evaluate expression in QlikSense ?

Can you please though more insight into this?


PS:Most of these might be available in the next release, and rest can be achieved building extesnions.


Thanks and Regards,

Sangram Reddy.

Not applicable

Re: Doubts regarding Qliksense

Hi paul,

Thanks for your reply. As you are saying, If and set analysis is workaround for "Enabling Conditional evaluation

of perticular exprssion". But what-if, when i have to show/hide column in straight table based on dimension selector?

reddys310
Honored Contributor II

Re: Doubts regarding Qliksense

Hi Devanada,

Conditional hiding of columns in a straight table is not yet available!

Not applicable

Re: Doubts regarding Qliksense

Hi Sangram,

Thanks for your reply.

I am preparing a document, What is not achieved yet in QlikSense as compared to Qlikview. If you more idea about it or have document already with you. Then please share.

Thanks.

reddys310
Honored Contributor II

Re: Doubts regarding Qliksense

Adding in an other point....there is no cyclic group option present but you can achieve this with calculated dimensions.

Most of the features in Qlikview can be achieved in qliksense by developing extensions.