Qlik Community

Qlik Sense App Development

Discussion board where members can learn more about Qlik Sense App Development and Usage.

shree909
Valued Contributor II

Calling the Bookmarks in the qliksense with a url

Hi Folks,

I have a scenario where i want to call  the bookmarks directly with the url

For that i have a  bookmark id,

Example:  Https:// localhost/sense/appid/bookmark/qjdl

https://xxx.xxxx.xxxx.xxxx//sense/app/d6bd61616/bookmark/qJdJ


For the standard URL I tried appending  the bookmarks

Tried with bookmark/qJdJ and Bookmark =qJdJ nothing works.


when i access this url its not opening the bookmark page.

Is there a way that we can call the bookmarks directly from the url.

i know in qlikview it works   but not in sense???

https://community.qlik.com/blogs/qlikviewdesignblog/2014/07/11/ajax-and-url-parameters#start=25

1 Solution

Accepted Solutions
Highlighted
Employee
Employee

Re: Calling the Bookmarks in the qliksense with a url

So, this works from 2.0. There are two ways, as I see it;

Have the bookmark in the URL

The syntax for bookmarks in the URL took some figuring out, but I got this working: https://mysenseserver/sense/app/4855acdb-2ab7-490b-9638-f34bd5d0723e/sheet/etGmEPq/state/analysis/bo...

That was on a 2.2 server. I got the bookmark ID from the Single Configurator, since the QMC does not show them for some reason.

Use the Single Configurator in the dev-hub

The Single Configurator is located at https://mysenseserver/dev-hub‌ (2.2) or https://mysenseserver/single (2.0, 2.1), and will allow to reference a single object via a link, and it would be any object - sheet or chart object. The URL to a single would be something like https://mysenseserver/single?appid=2511d22e-091f-4dee-b92b-d07042a3c42a&sheet=XPFUjr&opt=nointeracti...

It can contain either a selected bookmarks, or any combination of selections. It's very powerful.

6 Replies
Not applicable

Re: Calling the Bookmarks in the qliksense with a url

Hi,

Try https://xxx.xxxx.xxxx.xxxx//sense/app/d6bd61616?bookmark=qJdJ


Best regards

André R. Ferreira

shree909
Valued Contributor II

Re: Calling the Bookmarks in the qliksense with a url

Thanks for ur respose Andre, But that dint work....

Not applicable

Re: Calling the Bookmarks in the qliksense with a url

I am also looking for solution to this.  I would like to be able to open the bookmark with single URL.

Highlighted
Employee
Employee

Re: Calling the Bookmarks in the qliksense with a url

So, this works from 2.0. There are two ways, as I see it;

Have the bookmark in the URL

The syntax for bookmarks in the URL took some figuring out, but I got this working: https://mysenseserver/sense/app/4855acdb-2ab7-490b-9638-f34bd5d0723e/sheet/etGmEPq/state/analysis/bo...

That was on a 2.2 server. I got the bookmark ID from the Single Configurator, since the QMC does not show them for some reason.

Use the Single Configurator in the dev-hub

The Single Configurator is located at https://mysenseserver/dev-hub‌ (2.2) or https://mysenseserver/single (2.0, 2.1), and will allow to reference a single object via a link, and it would be any object - sheet or chart object. The URL to a single would be something like https://mysenseserver/single?appid=2511d22e-091f-4dee-b92b-d07042a3c42a&sheet=XPFUjr&opt=nointeracti...

It can contain either a selected bookmarks, or any combination of selections. It's very powerful.

reddys310
Honored Contributor II

Re: Calling the Bookmarks in the qliksense with a url

Hi Shree,

Use the Single Configurator to get the url when a book mark is selected. This will give you the right URL.

rbartley
Contributor III

Re: Calling the Bookmarks in the qliksense with a url

In fact, the relevant bit of the URL is bookmark=....... .  You can just add "?bookmark=....." to the URL (or "&bookmark...." if you already have other parameters in your URL) and it will apply the bookmark.

Community Browser