Qlik Community

QlikView Management

Discussion Board for collaboration on QlikView Management.

Not applicable

where QlikView Server 11 Users CALs add?

appeared in a version 10 User Cals button to add in -> Qlikview Management Console --> system --> Licenses --> Qlikview Server --> Client Access Licenses (CALs)---> Assigned CALs

this new Verson Qlikview Server 11  not see the Add User CALs button..

server11.jpg

Regards,

Edgar Ruiz

Tags (1)
1 Solution

Accepted Solutions
Emmanuelle-Bustos
Valued Contributor

where QlikView Server 11 Users CALs add?

It's as drehmann posted:

in your QV Server mangement consolo go to:

system>setup>DSC>Local Directory>         and change the path address to    local://<MyComputerName> then clic apply.

So you will can see and add users the way you asked for.

Regards!

22 Replies
lhr
Contributor III

where QlikView Server 11 Users CALs add?

the button to assign cals is the little picture of two green clad persons to the right just below the drop down.

cheers

Not applicable

where QlikView Server 11 Users CALs add?

Thanks for your answer..

This button opens the Manger User..

But users do not appear to exist in my system, nor let me add user new...

no_users.jpg

Thank you very much for your contributions

Edgar Ruiz

lhr
Contributor III

where QlikView Server 11 Users CALs add?

make sure you have configured the directory service connector properly.

Not applicable

where QlikView Server 11 Users CALs add?

I have no directory service, Only users named in the operating system

As him to add a user named?

Thank you very much for your answers

Edgar Ruiz

tle
Contributor II

where QlikView Server 11 Users CALs add?

You still need to configure the directory service by adding a local directory.

kim_rormark
New Contributor III

where QlikView Server 11 Users CALs add?

I will also do this one.

In QV Server 10 you could add a Document CAL or a User Lisence to a user by specifying the name of the user in a textbox that was just above the list of already added user. In QV Server 11 this textbox is removed.

How can I do this now? Because of the way the network is configured in my company, this was the only way to assign a user.

Not applicable

where QlikView Server 11 Users CALs add?

Hello Edgar,

      Can  you  tell me the  way ,you have configured your Dirrectory Service because i am having the same problem,.I have recently installed Qlikview Server v11.0 but dont knw how to add User. If you knw pls reply...

Not applicable

where QlikView Server 11 Users CALs add?

Hi Edgar,Kim and Devang

Was having a similar issue, but this should hopefully help. As mentioned above you need to configure the Directory Service Connectors(Systems→Setup→Directory Service Connectors).

In my one I already had an Active Directory and Local Directory set up but I needed to add a Path in each one (click on the add Path and enter details  - Path= put in your directory path(the directory your user id sits on I think.)

Once that is done for your directories, if you go back to the license tab and select manage users,and type in the user name now you should be able to see it.

Hope this helps

Not applicable

where QlikView Server 11 Users CALs add?

Hi Edgar,Kim and Devang

Was having a similar issue, but this should hopefully help. As mentioned above you need to configure the Directory Service Connectors(Systems→Setup→Directory Service Connectors).

In my one I already had an Active Directory and Local Directory set up but I needed to add a Path in each one (click on the add Path and enter details  - Path= put in your directory path(the directory your user id sits on I think.)

Once that is done for your directories, if you go back to the license tab and select manage users,and type in the user name now you should be able to see it.

Hope this helps

Community Browser