Qlik Community

QlikView Publisher

Discussion Board for collaboration on QlikView Publisher.

Announcements

Breathe easy -- you now have more time to plan your next steps with Qlik!
QlikView 11.2 Extended Support is now valid through December 31, 2020. Click here for more information.

onkellepie
Not applicable

Error in QVW - SE_LOG: Expression Error. Doc: QVW NAME ObjectId: , Expr(0)

Hi,

everytime i open an Special qvw i got the following message in Windows Eventlog

Event ID: 300

SE_LOG: Expression Error. Doc: QVWNAME.QVW, ObjectId: , Expr(0)

The QVW works fine and there are no Problems. But there is the eventlog entry. How can i check where the error occurs? There is no ObjectId specified in eventlog entry. So i assume a General error in formula list or variable list. Or perhaps in properties of a sheet. I checked all Sheets and the variable list. But there is no highlighted error.

Did anybody know how i can check if a qvw contains General Errors?

Thanks for your help!

Regards

We use QV 11.2 SR 12

1 Solution

Accepted Solutions
onkellepie
Not applicable

Re: Error in QVW - SE_LOG: Expression Error. Doc: QVW NAME ObjectId: , Expr(0)

We solve the Problem. The Problem was a deleted object in qvw.

We use -prj Folders with TFS for source control. So we delete the qvw, create a new one and named it like the deleted qvw. Then we open this qvw and save it again. The error never occured again.

if you did not have a -prj folder you must create it before deleting. You only create a new folder with name of your qvw and the extension "-prj". i.e. Your qvw is called "MyTest.qvw" you create a new Folder "MyTest-prj". When you open myTest.qvw and save it, you have many files in "prj" folder.

Thanks Community for your help!

6 Replies
Chanty4u
Not applicable

Re: Error in QVW - SE_LOG: Expression Error. Doc: QVW NAME ObjectId: , Expr(0)

Bill_Britt
Not applicable

Re: Error in QVW - SE_LOG: Expression Error. Doc: QVW NAME ObjectId: , Expr(0)

Hi,

This issue has been fixed in SR13 with a setting to turn the error off.

Bill

Bill - Designated Support Engineer at Qlik
If a post helps to resolve your issue, please mark the appropriate replies as CORRECT.
onkellepie
Not applicable

Re: Error in QVW - SE_LOG: Expression Error. Doc: QVW NAME ObjectId: , Expr(0)

Hi Chanty,

thanks for your Response. But the error occurs when i open the qvw in accesspoint, not when i reload the qvw. 

onkellepie
Not applicable

Re: Error in QVW - SE_LOG: Expression Error. Doc: QVW NAME ObjectId: , Expr(0)

Hi Bill,

i dont want to turn the error off. I want to fix the error. Is there any possibilty to find the point where the error occurs?

Peter_Cammaert
Not applicable

Re: Error in QVW - SE_LOG: Expression Error. Doc: QVW NAME ObjectId: , Expr(0)

That's a tricky one, and as far as I know there is no easy detection method.

The most probable cause for this error is that a field that is used in one of the expressions has disappeared, been renamed or its name has been mispelled. So I would advise to check all expressions that are not used in objects for wrong field names. For example, did you define any document level triggers that aren't used anymore? Do they carry expressions?

Best,

Peter

onkellepie
Not applicable

Re: Error in QVW - SE_LOG: Expression Error. Doc: QVW NAME ObjectId: , Expr(0)

We solve the Problem. The Problem was a deleted object in qvw.

We use -prj Folders with TFS for source control. So we delete the qvw, create a new one and named it like the deleted qvw. Then we open this qvw and save it again. The error never occured again.

if you did not have a -prj folder you must create it before deleting. You only create a new folder with name of your qvw and the extension "-prj". i.e. Your qvw is called "MyTest.qvw" you create a new Folder "MyTest-prj". When you open myTest.qvw and save it, you have many files in "prj" folder.

Thanks Community for your help!