When I reload the "trigger _bat.qvw" with QV desktop, the bat is running correctly and the "C:\QV_FILE\test_qv_01.qvw" is reloaded.
However, when I place it in server and setup reload task to reload "trigger _bat.qvw" , it do not pop out any error, but it keeps reloading and reloading.
Under task log:
(6/7/2023 9:07:30 PM) Information: Opening "C:\QV_FILE\Trigger bat for app reload 01.qvw"
(6/7/2023 9:07:30 PM) Information: Allocating new QlikView Engine. Current usage count=0 of 4 (of type non-reader).
(6/7/2023 9:07:30 PM) Information: Max retries:5
(6/7/2023 9:07:30 PM) Information: Attempt:01
(6/7/2023 9:07:32 PM) Information: Opened the QlikView Engine successfully. ProcessID=16720
(6/7/2023 9:07:32 PM) Information: Allocated QlikView Engine successfully. Current usage count=1 of 4 (of type non-reader). Ticket number=3.
(6/7/2023 9:07:32 PM) Information: Loading document "C:\QV_FILE\Trigger bat for app reload 01.qvw" (0.15 Mb)
(6/7/2023 9:07:32 PM) Information: Physical FileSize=0.15 Mb. Memory Allocation Delta for this file=2.84 Mb. Available Physical Memory Before Open=5608.47 Mb. Available Physical Memory After Open=5603.32 Mb. Total Physical Memory=7999.55 Mb.
(6/7/2023 9:07:32 PM) Information: Attempted to load the document without data.
(6/7/2023 9:07:32 PM) Information: The document was loaded successfully.
(6/7/2023 9:07:32 PM) Information: Document was opened successfully
(6/7/2023 9:08:05 PM) Information: Slow down logging. Log every <10> seconds.
The only thing I can do is manually abort the task.
I understand there are standard reload function in QMC for document reload. However, as I am creating a chained task including call to NP API (to replace the function of reload task in old NP16), so under my scenario, I must use bat approach to trigger reload of QVW.
has the qmc user the appropriate access rights to the bat ?
has the qmc user a valid QlikView licence ?
also by other called tools like NP, Excel and so on - exists valid licences ?
is any section access applied ?
any OnOpen actions/macros ?
are the user- and document security-properties properly set
is the AllowExecuteCommand setting applied within the settings.ini
probably some more reasons ...
At first try to execute with the qmc-user on the server the batch manually which should exclude most of the access and licence stuff and also any possible popup-queries asking to allow or config anything. Helpful may also the following links:
Just to clear it - the batch is starting and performing the included actions but not finishing properly and therefore the qmc-task is waiting for any (error/success) response or the batch is starting but not executing anything or the batch didn't start?
At first I suggest to check the information + links from above again and ensuring that the user + document properties are properly set. This might be done by opening the qvw with the EXECUTE directly with the qmc-user in the desktop client and performing the reload.
If the above worked but not triggered per qmc-task check again that AllowExecuteCommand is set properly and within the right settings.ini - this means not the "normal" settings.ini within the QlikView server folder else the one within System32.
Further helpful would be to log the batch-results which could be reached by adding a >> Path/Filename.log to execute-statement and if the batch itself is starting some similar logic within the batch-routine and/or within the called tools. Finding the breaking point is quite near to finding the cause.
