
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
What are the steps to integrate keycloak with qliksense
Hi all can anyone help me with integration of keycloak with qliksense, i followed https://community.qlik.com/t5/Official-Support-Articles/Qlik-Sense-for-Windows-How-to-configure-OIDC... but it didint work, can anyone help me with all steps to configure it in qmc
- « Previous Replies
-
- 1
- 2
- Next Replies »
Accepted Solutions

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
@Micky123 the Redirect URI is not the same as the OpenID connect metadata URI .
Refer here this explains where in the keyclaok admin console the redirect uri's are configured
"And do I have to specify OIDC attribute mapping while configuring Virtual proxy?"
The the virtual proxy should be configured as below.

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi @Mick if you are unable to set up Keycloak as an IDP using the official Qlik guide .You will need to reach out to our Professional Services team for assistance.
How-and-when-to-contact-Qlik-s-Professional-Services

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi @Micky123
If you can tell us exactly which error you're running into, maybe someone can suggest something.
Fetch the information listed here, anonymize them and post it here
https://community.qlik.com/t5/Official-Support-Articles/Qlik-sense-for-Windows-Information-needed-to...
There is not enough details at this point for us to understand what is your issue.
Otherwise, as Eugene suggested, you can also reach out to Qlik consulting services to have someone perform the setup for you.

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I am using enterprise edition, i configured virtual proxy with keycloak details and linked it to proxy server. Now i again try to access the proxy server it authenticates with the windows authentication as it was doing earlier. It doesn,t redirect to keycloak.

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Are you including your virtual proxy prefix in the URL when you try to access ?
https://servername/virtualproxyprefix/hub
For example:
https://qlikserver1.qlik.com/keycloak/hub

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
@Damien_V Yes it shows internal server error-500

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Are https://community.qlik.com/t5/Official-Support-Articles/Qlik-Sense-for-Windows-How-to-configure-OIDC... these steps enough to integrate the keycloak or we need to do something else.
I added node for load balancing and the server host name as host allow list

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Which version of keycloak are you using? The article was written for keycloak 13.0 and there might be slight changes on the setup since the UI in keycloak has changed since version 20.0
Is this an error 500 with a keycloak logo or an error 500 with a Qlik Sense logo?
You can check in the Qlik Sense Proxy logs, at the time when you get the error 500, you should see an error message telling you what is not set up correctly.
C:/Programdata/Qlik/Sense/log/Proxy/Trace/Servername_Audit_Proxy.txt

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
@Damien_V I am using qliksense version 14 -November 2021 and I am getting error with Qlik sense logo.
And about Proxy log, I haven.t installed anything locally. I have been given the access to qmc by my organization. How can I watch proxy logs ?

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
@Micky123 You need Remote Desktop access to the Qlik Sense server in order to see the logs.

- « Previous Replies
-
- 1
- 2
- Next Replies »