Skip to main content
Announcements
Defect acknowledgement with Nprinting Engine May 2022 SR2, please READ HERE
cancel
Showing results for 
Search instead for 
Did you mean: 
Raju_6952
Creator III
Creator III

Issue with data

Hi,

 

I have created a pixel perfect report in nprintinng designer and preview is working fine ,but when the same report is scheduled or manually triggered from the publish task then one of the value is showing zero even after updating the connection meta data and recreated the same object again and also new publish task but nothing helping much.

Any suggestions would be highly appreciated.

 

Note: I am using Qlik sense June 2019 version enterprise edition and Qlik nprintinng designer May 2022, Nprinting version February 2021.

Kind Regards,

Raju

Labels (1)
1 Solution

Accepted Solutions
Frank_S
Support
Support

Further, you are in a very unsupported state. See points 1 and 2 below:

 

1. you're NP server and designer are not the same version. They MUST be the same version. Please upgrade your NPrinting server so that it matches the NPrinting designer May 2022. Recommend upgrading both to May 2022 SR 4. (NPrinting Feb. 2021 is no longer supported).

https://help.qlik.com/en-US/nprinting/May2023/Content/NPrinting/ReportsDevelopment/Common-editing-fe...

  • Qlik NPrinting Designer must be the same version as Qlik NPrinting Server.

2. Qlik sense June 2019 version enterprise edition is no longer supported.

 

Qlik Sense compatibility

Qlik NPrinting May 2022 is compatible with the following Qlik Sense versions:

  • Minimum supported version is Qlik Sense Enterprise on Windows August 2020.

 

Finally, if you have a report filter and a task filter that references the same dimension, this too can cause the issue. Using the same filter dimensions in a report and a a task will result in task failures.

https://help.qlik.com/en-US/nprinting/May2022/Content/NPrinting/ReportsDevelopment/Static-dynamic-fi...

My reports fail to generate

Possible cause  

Your report uses the same dimension in the task, user, report, and object filter hierarchy.

 

Kind regards...

 

 

 

Please remember hit the 'Like' button and for helpful answers and resolutions, click on the 'Accept As Solution' button. Cheers!

View solution in original post

5 Replies
MayilVahanan

Hi

Might be, Is any section access or filter is affecting the report??

Thanks & Regards, Mayil Vahanan R
Please close the thread by marking correct answer & give likes if you like the post.
Raju_6952
Creator III
Creator III
Author

Hi @MayilVahanan ,

 

I get this issue when date filter is applied to the task, without filter its working fine.

 

 The formulae used is Date(num(Today()-1))

MayilVahanan

Hi

Try like below and verify once

Date(num(Today(1)-1), 'YourDateFormat')

Thanks & Regards, Mayil Vahanan R
Please close the thread by marking correct answer & give likes if you like the post.
Raju_6952
Creator III
Creator III
Author

Hi @MayilVahanan ,

Date(num(Today(1)-1), 'YourDateFormat')

By using above the output is in date# format.

Frank_S
Support
Support

Further, you are in a very unsupported state. See points 1 and 2 below:

 

1. you're NP server and designer are not the same version. They MUST be the same version. Please upgrade your NPrinting server so that it matches the NPrinting designer May 2022. Recommend upgrading both to May 2022 SR 4. (NPrinting Feb. 2021 is no longer supported).

https://help.qlik.com/en-US/nprinting/May2023/Content/NPrinting/ReportsDevelopment/Common-editing-fe...

  • Qlik NPrinting Designer must be the same version as Qlik NPrinting Server.

2. Qlik sense June 2019 version enterprise edition is no longer supported.

 

Qlik Sense compatibility

Qlik NPrinting May 2022 is compatible with the following Qlik Sense versions:

  • Minimum supported version is Qlik Sense Enterprise on Windows August 2020.

 

Finally, if you have a report filter and a task filter that references the same dimension, this too can cause the issue. Using the same filter dimensions in a report and a a task will result in task failures.

https://help.qlik.com/en-US/nprinting/May2022/Content/NPrinting/ReportsDevelopment/Static-dynamic-fi...

My reports fail to generate

Possible cause  

Your report uses the same dimension in the task, user, report, and object filter hierarchy.

 

Kind regards...

 

 

 

Please remember hit the 'Like' button and for helpful answers and resolutions, click on the 'Accept As Solution' button. Cheers!